Blog Detail

Home / Blog / 8 Reasons Why Your KitchenAid Dishwasher Leaves Dishes WetWas this helpful?

8 Reasons Why Your KitchenAid Dishwasher Leaves Dishes WetWas this helpful? image
8 Reasons Why Your KitchenAid Dishwasher Leaves Dishes WetWas this helpful?

It’s the end of a long day. You’ve just had a delightful home-cooked meal, and now it’s time to clean the dishes. But, what’s this? Does your Kitchenaid dishwasher not dry dishes? That isn’t what you agreed to do. Fortunately, we’ve got the help you need to troubleshoot and solve this all-too-common issue.

When Your KitchenAid Dishwasher Leaves Dishes Wet, Do This

Lets roll up our sleeves, don on our detective hats, and get to the root of these KitchenAid dishwasher drying woes with some troubleshooting tips and tricks!

Incorrect Dishwasher Loading

One of the highest causes that your are getting dishes wet in your Kitchenaid dishwasher is because you are loading the dishes wrong. Yes, the way you position your dishes can affect how they dry. Overstuffed or misarranged dishes may hamper air flow, leaving wet dishes at the end of the cycle.

Solution:

To keep this from happening, make sure items like cups and glasses are always placed on the top rack facing the floor and that plates and larger utensils are turned in toward the center on the lower rack.

Additionally, don't nest dishes too closely and avoid overloading the dishwasher.

With these steps, you facilitate the passage of air and allow your strains to dry better.

Dishwasher Cycle Settings

It might be that your dishwasher settings aren’t suitable to dry thoroughly. One comment was that the heated dry on some modern dishwashers may not be default and they're energy efficient. If you have new-ish Kitchenaid dishwasher not drying, check this first.

Solution:

You can manually activate the heated dry feature by pressing a button on the control panel that says “Heated Dry” or words to that effect.

Keep in mind, those quick-wash or express-wash options sometimes omit adding a heated dry cycle so it can save time.

Inadequate Use of Rinse Aid

If your Kitchenaid dishwasher is leaving dishes wet sometimes, you may not be using rinse aid the right way. Rinse agents simply lessens the water surface tension, so it can drain off of dishes better. This helps eliminate water spots and allows for quicker drying.

Solution:

Keep the rinse-aid dispenser, usually located at the side of the detergent dispenser, topped up.

If the dispenser is full and you still have problems, there could be a buildup preventing the rinse aid from dispensing. A fast clean with white vinegar ought to work.

Dishwasher Door Opens Too Soon

If you’re the type who throws open the dishwasher the minute the cycle ends, chances are you have a KitchenAid dishwasher condensation problem and don’t even realize it. If you open the dishwasher door too fast it can shoot a burst of cool air at the contents and the warm moisture that remains inside will re-condense on your dishes and then your KitchenAid dishwasher not drying the dishes.

Solution:

Let the dishwasher finish its cycle before opening the door. Just know that if you do it early you’re getting wet dishes.

Blocked Drain Filter

A blocked drain filter, like a blocked drain hose, can impede your dishwasher’s drainage. Food particles tend to accumulate in that filter, and if you fail to clean it periodically, itmay slow down the drainage.

Solution:

Inspect the filter: Regularly examining the condition of your dishwasher filter is crucial. The filter can typically be found at the base of your dishwasher tub, and generally can be simply unscrewed for closer inspection.

Clean the filter: You may need to rinse it under warm running water,or lightly brush off the gathered debris, based on the degree of filth on its surface. Just make sure not to use anything too abrasive or sharp in order to avoid damaging the filter.

Install the filter back: Properly reinstall the filter after the clean. Filters that are reinstalled incorrectly may cause poor filtration and addional problems.

Faulty Heating Element

The dishwasher’s heating element serves two purposes: it heats the water, and it helps dry the dishes after they’ve been washed. If your heating element is bad your dishes may not be dry by the end of the cycle.

Solution:

After a cycle, see if your dishes are hot to the touch; if not, the heating element might be faulty and should be replaced.

Clogged Drain Hose

If you’re seeing standing water at the bottom of the dishwasher and wet dishes, this could mean that your drain hose is clogged. The water may not be exiting your dishwasher as quickly as is it being filled, which could be a result of either a slow draining or clogged drain hose.

Solution:

Inspect the drain hose for blockages and remove if necessary.

Run a cycle just once to make sure there is no contamination from the backflow water.

Non-Functioning Drain Pump

If the drain pump is bad, wash and rinse water may not exit the dishwasher correctly, resulting in wet dishes.

Solution:

Listen for the sound of the pump when the cycles change; odd noises, or no noise at all, could signal that something is wrong.

There is a caveat: Inspecting the drain pump may involve some disassembly of the dishwasher, a task that should probably be left to a pro.